CVSS: -EPSS: 0%CPEs: 8EXPL: 0CVE-2024-50234 – wifi: iwlegacy: Clear stale interrupts before resuming device
https://notcve.org/view.php?id=CVE-2024-50234
In the Linux kernel, the following vulnerability has been resolved: wifi: iwlegacy: Clear stale interrupts before resuming device iwl4965 fails upon resume from hibernation on my laptop. The reason seems to be a stale interrupt which isn't being cleared out before interrupts are enabled. We end up with a race beween the resume trying to bring things back up, and the restart work (queued form the interrupt handler) trying to bring things down. Eventually the whole thing blows up. Fix the problem by clearing out any stale interrupts before interrupts get enabled during resume. Here's a debug log of the indicent: [ 12.042589] ieee80211 phy0: il_isr ISR inta 0x00000080, enabled 0xaa00008b, fh 0x00000000 [ 12.042625] ieee80211 phy0: il4965_irq_tasklet inta 0x00000080, enabled 0x00000000, fh 0x00000000 [ 12.042651] iwl4965 0000:10:00.0: RF_KILL bit toggled to enable radio. [ 12.042653] iwl4965 0000:10:00.0: On demand firmware reload [ 12.042690] ieee80211 phy0: il4965_irq_tasklet End inta 0x00000000, enabled 0xaa00008b, fh 0x00000000, flags 0x00000282 [ 12.052207] ieee80211 phy0: il4965_mac_start enter [ 12.052212] ieee80211 phy0: il_prep_station Add STA to driver ID 31: ff:ff:ff:ff:ff:ff [ 12.052244] ieee80211 phy0: il4965_set_hw_ready hardware ready [ 12.052324] ieee80211 phy0: il_apm_init Init card's basic functions [ 12.052348] ieee80211 phy0: il_apm_init L1 Enabled; Disabling L0S [ 12.055727] ieee80211 phy0: il4965_load_bsm Begin load bsm [ 12.056140] ieee80211 phy0: il4965_verify_bsm Begin verify bsm [ 12.058642] ieee80211 phy0: il4965_verify_bsm BSM bootstrap uCode image OK [ 12.058721] ieee80211 phy0: il4965_load_bsm BSM write complete, poll 1 iterations [ 12.058734] ieee80211 phy0: __il4965_up iwl4965 is coming up [ 12.058737] ieee80211 phy0: il4965_mac_start Start UP work done. [ 12.058757] ieee80211 phy0: __il4965_down iwl4965 is going down [ 12.058761] ieee80211 phy0: il_scan_cancel_timeout Scan cancel timeout [ 12.058762] ieee80211 phy0: il_do_scan_abort Not performing scan to abort [ 12.058765] ieee80211 phy0: il_clear_ucode_stations Clearing ucode stations in driver [ 12.058767] ieee80211 phy0: il_clear_ucode_stations No active stations found to be cleared [ 12.058819] ieee80211 phy0: _il_apm_stop Stop card, put in low power state [ 12.058827] ieee80211 phy0: _il_apm_stop_master stop master [ 12.058864] ieee80211 phy0: il4965_clear_free_frames 0 frames on pre-allocated heap on clear. [ 12.058869] ieee80211 phy0: Hardware restart was requested [ 16.132299] iwl4965 0000:10:00.0: START_ALIVE timeout after 4000ms. [ 16.132303] ------------[ cut here ]------------ [ 16.132304] Hardware became unavailable upon resume. This could be a software issue prior to suspend or a hardware issue. [ 16.132338] WARNING: CPU: 0 PID: 181 at net/mac80211/util.c:1826 ieee80211_reconfig+0x8f/0x14b0 [mac80211] [ 16.132390] Modules linked in: ctr ccm sch_fq_codel xt_tcpudp xt_multiport xt_state iptable_filter iptable_nat nf_nat nf_conntrack nf_defrag_ipv4 ip_tables x_tables binfmt_misc joydev mousedev btusb btrtl btintel btbcm bluetooth ecdh_generic ecc iTCO_wdt i2c_dev iwl4965 iwlegacy coretemp snd_hda_codec_analog pcspkr psmouse mac80211 snd_hda_codec_generic libarc4 sdhci_pci cqhci sha256_generic sdhci libsha256 firewire_ohci snd_hda_intel snd_intel_dspcfg mmc_core snd_hda_codec snd_hwdep firewire_core led_class iosf_mbi snd_hda_core uhci_hcd lpc_ich crc_itu_t cfg80211 ehci_pci ehci_hcd snd_pcm usbcore mfd_core rfkill snd_timer snd usb_common soundcore video parport_pc parport intel_agp wmi intel_gtt backlight e1000e agpgart evdev [ 16.132456] CPU: 0 UID: 0 PID: 181 Comm: kworker/u8:6 Not tainted 6.11.0-cl+ #143 [ 16.132460] Hardware name: Hewlett-Packard HP Compaq 6910p/30BE, BIOS 68MCU Ver. • https://git.kernel.org/stable/c/271d282ecc15d7012e71ca82c89a6c0e13a063dd https://git.kernel.org/stable/c/9d89941e51259c2b0b8e9c10c6f1f74200d7444f https://git.kernel.org/stable/c/d0231f43df473e2f80372d0ca150eb3619932ef9 https://git.kernel.org/stable/c/8ac22fe1e2b104c37e4fecd97735f64bd6349ebc https://git.kernel.org/stable/c/23f9cef17ee315777dbe88d5c11ff6166e4d0699 https://git.kernel.org/stable/c/cedf0f1db8d5f3524339c2c6e35a8505b0f1ab73 https://git.kernel.org/stable/c/8af8294d369a871cdbcdbb4d13b87d2d6e490a1f https://git.kernel.org/stable/c/07c90acb071b9954e1fecb1e4f4f13d12 •
CVSS: -EPSS: 0%CPEs: 3EXPL: 0CVE-2024-50211 – udf: refactor inode_bmap() to handle error
https://notcve.org/view.php?id=CVE-2024-50211
In the Linux kernel, the following vulnerability has been resolved: udf: refactor inode_bmap() to handle error Refactor inode_bmap() to handle error since udf_next_aext() can return error now. On situations like ftruncate, udf_extend_file() can now detect errors and bail out early without resorting to checking for particular offsets and assuming internal behavior of these functions. • https://git.kernel.org/stable/c/493447dd8336607fce426f7879e581095f6c606e https://git.kernel.org/stable/c/b22d9a5698abf04341f8fbc30141e0673863c3a6 https://git.kernel.org/stable/c/c226964ec786f3797ed389a16392ce4357697d24 •
CVSS: -EPSS: 0%CPEs: 5EXPL: 0CVE-2024-50196 – pinctrl: ocelot: fix system hang on level based interrupts
https://notcve.org/view.php?id=CVE-2024-50196
In the Linux kernel, the following vulnerability has been resolved: pinctrl: ocelot: fix system hang on level based interrupts The current implementation only calls chained_irq_enter() and chained_irq_exit() if it detects pending interrupts. ``` for (i = 0; i < info->stride; i++) { uregmap_read(info->map, id_reg + 4 * i, ®); if (!reg) continue; chained_irq_enter(parent_chip, desc); ``` However, in case of GPIO pin configured in level mode and the parent controller configured in edge mode, GPIO interrupt might be lowered by the hardware. In the result, if the interrupt is short enough, the parent interrupt is still pending while the GPIO interrupt is cleared; chained_irq_enter() never gets called and the system hangs trying to service the parent interrupt. Moving chained_irq_enter() and chained_irq_exit() outside the for loop ensures that they are called even when GPIO interrupt is lowered by the hardware. The similar code with chained_irq_enter() / chained_irq_exit() functions wrapping interrupt checking loop may be found in many other drivers: ``` grep -r -A 10 chained_irq_enter drivers/pinctrl ``` • https://git.kernel.org/stable/c/655f5d4662b958122b260be05aa6dfdf8768efe6 https://git.kernel.org/stable/c/4a81800ef05bea5a9896f199677f7b7f5020776a https://git.kernel.org/stable/c/20728e86289ab463b99b7ab4425515bd26aba417 https://git.kernel.org/stable/c/dcbe9954634807ec54e22bde278b5b269f921381 https://git.kernel.org/stable/c/93b8ddc54507a227087c60a0013ed833b6ae7d3c •
CVSS: -EPSS: 0%CPEs: 5EXPL: 0CVE-2024-50191 – ext4: don't set SB_RDONLY after filesystem errors
https://notcve.org/view.php?id=CVE-2024-50191
In the Linux kernel, the following vulnerability has been resolved: ext4: don't set SB_RDONLY after filesystem errors When the filesystem is mounted with errors=remount-ro, we were setting SB_RDONLY flag to stop all filesystem modifications. We knew this misses proper locking (sb->s_umount) and does not go through proper filesystem remount procedure but it has been the way this worked since early ext2 days and it was good enough for catastrophic situation damage mitigation. Recently, syzbot has found a way (see link) to trigger warnings in filesystem freezing because the code got confused by SB_RDONLY changing under its hands. Since these days we set EXT4_FLAGS_SHUTDOWN on the superblock which is enough to stop all filesystem modifications, modifying SB_RDONLY shouldn't be needed. So stop doing that. • https://git.kernel.org/stable/c/fbb177bc1d6487cd3e9b50ae0be2781b7297980d https://git.kernel.org/stable/c/4061e07f040a091f694f461b86a26cf95ae66439 https://git.kernel.org/stable/c/58c0648e4c773f5b54f0cb63bc8c7c6bf52719a9 https://git.kernel.org/stable/c/ee77c388469116565e009eaa704a60bc78489e09 https://git.kernel.org/stable/c/d3476f3dad4ad68ae5f6b008ea6591d1520da5d8 •
CVSS: -EPSS: 0%CPEs: 7EXPL: 0CVE-2024-50184 – virtio_pmem: Check device status before requesting flush
https://notcve.org/view.php?id=CVE-2024-50184
In the Linux kernel, the following vulnerability has been resolved: virtio_pmem: Check device status before requesting flush If a pmem device is in a bad status, the driver side could wait for host ack forever in virtio_pmem_flush(), causing the system to hang. So add a status check in the beginning of virtio_pmem_flush() to return early if the device is not activated. • https://git.kernel.org/stable/c/59ac565c6277d4be6661e81ea6a7f3ca2c5e4e36 https://git.kernel.org/stable/c/4ce662fe4be6fbc2595d9ef4888b2b6e778c99ed https://git.kernel.org/stable/c/9a2bc9b6f929a2ce1ebe4d1a796ddab37568c5b4 https://git.kernel.org/stable/c/6a5ca0ab94e13a1474bf7ad8437a975c2193618f https://git.kernel.org/stable/c/b01793cc63dd39c8f12b9a3d8dc115fbebb19e2a https://git.kernel.org/stable/c/ce7a3a62cc533c922072f328fd2ea2fd7cb893d4 https://git.kernel.org/stable/c/e25fbcd97cf52c3c9824d44b5c56c19673c3dd50 •